Magnet_MK10 V2

€6.78

€8.48

Prix SPECIAL jusqu'au 09/08/2024

The Magnet_MK10 allows to connect your extruder to the hotend in bowden mode.

Screwed on extruder side and magnet on hotend side.

System improved & guaranteed for 2 years on our hotends.

The solution to the problems of broken pneufits, gnawed PTFE tube, mechanical play, missed prints .....

Mounting on most Chinese printers (Cr10, Ender, Tevo, Alfawise,biquB1 etc ...) and hotend clone E3D

Lenght

Quality

Extrudeur

Quantity

Composition du kit :

1 x PTFE tube 2 x 4mm or Capricorn XS 1.9 x 4mm (length 32, 45, 65 or 100 cm) with M6-G1/8 threaded brass insert on the extruder side and a magnet.
1 x 65 mm PTFE or Capricorn XS tube (inside hotend)
1 x knurled and threaded steel subbase in G1/8 ( M10)
4 x M3 washers (depending on printer)

For printers with Titan & Bondtech extruder, a STL is supplied (see "Attached documents" tab).

Caution, the Neodymium magnet cannot withstand an ambient temperature of +85°C .

1 - How to choose your MagnetMK10 ?

	Remove the connection of your extruder as well as your hotend.Dismantle your hotend and clean it.
	Use the 65 mm PTFE or Capricorn XS tip (included in the kit).
	Push the PTFE or Capricorn XS tube into the stop. If you do this operation with the hotend mounted, it is best to heat the hotend so that the tube is in contact with the nozzle.
	Screw the knurled piece onto the hotend and tighten it manually.
	Very important step ! Using a cutter, gradually cut the PTFE tube all the way round. Do not cut it all at once, so that the cut is perpendicular and flush with the workpiece.
	Put 4 washers on the 2 fixing screws of the hotend.
	Fix your hotend on the X trolley. Check that the knurled piece is not in contact with the right hand screw of the trolley. To check this, unscrew/re-screw the knurled piece.
	Take the PTFE tube from our kit and screw the M6 or G1/8 brass fitting onto your extruder. CAUTION, tighten slightly or the part will break. A STL is provided at the bottom of the page for Titan & Bondtech extruders to screw the brass part (see photo in the product description)
	Insert a filament into your extruder and pull it out of the PTFE tube. Insert the filament into the hotend to center the assembly.
	Come and put the magnet in contact with the hotend. You have just finished assembling the "Magnet MK10" !!
	Tip : To disconnect the magnet, remove the filament from the hotend and slide the magnet to the right or left.

Brand Hotends.FR

Reference MMK10-M6-32-PTFE

Download (423.23KB)

Download (378.3KB)

Adaptateur pour monter le MagnetMK10 sur Wanaho D12

Download (503.11KB)

Show attestation

1★

2★

3★

4★

311

5★

9.8/10

Based on 338 reviews

Thierry b.
Published 11/08/2024 à 18:31 (Order date: 31/07/2024)

5

super
Christophe K.
Published 18/07/2024 à 17:57 (Order date: 05/07/2024)

5

Parfait. Comme decrit.
Thierry A.
Published 08/07/2024 à 13:23 (Order date: 25/06/2024)

5

Redonne vie à ma Ender3v2.
Jérôme B.
Published 28/06/2024 à 16:22 (Order date: 18/06/2024)

5

parfait merci !
Frederic b.
Published 16/05/2024 à 21:15 (Order date: 30/06/2023)

5

Au top